- Can I put gravel over grass to make it a driveway?
- How thick should the base be for a concrete driveway?
- Should you put plastic under concrete?
- How many inches of gravel do you need for a concrete slab?
- Can you pour concrete directly on dirt?
- Is wire mesh necessary in concrete driveway?
- How much does it cost to install a concrete driveway?
- How much does it cost to excavate a driveway?
- How long does it take to put in a new driveway?
- How deep should a sub base be for a driveway?
- Do you need gravel under concrete driveway?
- How deep should you dig for a driveway?
- What type of gravel is used under concrete?
- How do you prepare the ground before pouring concrete?
Can I put gravel over grass to make it a driveway?
You can lay the barrier right on top of the grass without mowing.
Keep in mind what the gravel is intended to support.
If it is heavy trucks, then at least a base layer of larger stone is needed under the gravel.
Place the soil barrier under the stone..
How thick should the base be for a concrete driveway?
four inchesAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
Should you put plastic under concrete?
Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.
How many inches of gravel do you need for a concrete slab?
Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete.
Can you pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
Is wire mesh necessary in concrete driveway?
When it comes to concrete, you can’t avoid cracks entirely, but wire mesh reinforcement will help hold the material together when they do occur. Also, it will help evenly distribute the weight of cars on your driveway. The added strength of steel is especially crucial if your subgrade isn’t up to par.
How much does it cost to install a concrete driveway?
Most concrete driveway installation costs between $1,800 and $6,000 or $4 to $15 per square foot. The average is just above $3,000 or $6 per square foot. Factors like location, size, decorative elements, potential reinforcement and removing the existing surface can all influence that range.
How much does it cost to excavate a driveway?
Excavate Driveway national average cost The national average materials cost to excavate driveway is $0.85 per square foot, with a range between $0.80 to $0.91. The total price for labor and materials per square foot is $2.39, coming in between $1.48 to $3.30.
How long does it take to put in a new driveway?
Under most conditions, you will be able to drive on the driveway within two to three days. But it can take 30 days or more for asphalt to fully cure.
How deep should a sub base be for a driveway?
100mmThe depth of the sub-base will depend on the size of vehicles using the drive with a typical domestic construction requiring a minimum depth of 100mm but preferably 150mm to be able to take cars. The most common sub-base material is DT Type 1 (MOT) which consists of crushed rock graded from 40mm down to dust.
Do you need gravel under concrete driveway?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
How deep should you dig for a driveway?
The excavation depth for a typical domestic driveway is 200-250mm below finished paving level, based on 100-150mm sub-base, 40mm sand bed and 50mm block.
What type of gravel is used under concrete?
“Six inches of well-graded gravel or crushed stone material properly compacted will give good results,” said Mark Conrardy, a sales engineer manager for Wacker Corp., Menomonee Falls, Wis. When properly compacted, both native soils or imported granular materials can provide good support.
How do you prepare the ground before pouring concrete?
Preparation is the most important aspect of pouring a concrete slab.Dig the ground down to the proper depth. … Smooth out the ground with the flat side of a rake so that you have a level surface. … Tamp the ground with a hand tamper or mechanical tamper. … Pour 2 inches of small, rounded gravel for additional drainage needs.